View Full Version : Need Info/Pics On Williams Extra Exhaust Mount
as far as im aware the willy has a centre section mount for the exhaust, to stop it hanging so low
does anyone have any pics of it, as im takin my car in on tuesday to get a little split welded up and ive asked them to make a mount, so if poss id like it the same as a williams one
Unfortunatly this is not the best picture of it
http://homepage.ntlworld.com/peterj.jones/Hosted%20Stuff/Exhaust%20Hanger.jpg
And this is the hanger on the exhaust:
http://homepage.ntlworld.com/peterj.jones/My%20Williams%20Pics/Project%20Pictures/Devil%20Exhaust%202.jpg
On my mount i have it held on by bolts, and have spacer plates behind it to bring it out to the hanger on the exhaust, and i have welded a washer onto the end of the clamp bar to stop the rubber slipping off if it isnt perfectly alined.
Heres a paint special of the plate if its any use.
http://homepage.ntlworld.com/peterj.jones/Hosted%20Stuff/Exhaust%20Hanger%20Picture.jpg
thanks for that mate, brilliant post
ive never seen it before so wasnt sure where on the car it was
is yours a willy or have you done this mod yourself ?
No worrys.
Its a Williams so it came with the mount, but i had to drill this mount off the car.
Because the hanger on the exhaust didnt line up with the hanger on the car so i modified it to suit.
Its worth putting the washer on the end of the hanger imo as where it is, it can come off. If there wasnt enough tension on it.
Really good mount though, as it stops the exhaust hanging low as you can see.
Shame not many exhausts come with that hanger though.
do you think its likely that a valver would have holes on the body to mount such a plate if it was made, as the bar welded to the exhaust is the easy part
BRUN,
I very much suspect that valvers have the holes as required on the tunnel.
If not, then buy the mount plate (should be a standard reno part - sorry don't have dialogys) and drill holes as appropriate, it would be very easy to do, as access is very easy once the exhaust is off. Probably even be able to do it with the exhaust on.
See this attachment for the location of the holes.
This is the underside of ARJ's old valver, so means valvers are drilled with those holes.
You can clearly see the reinforcement plate where the two holes should be. This is where you bolt the extra mount to.
Justin..
06-04-2007, 01:42
Part number for the mount :-
60 01 025 886 SUPPORT 12.65 ---3 x 1
MatBrown
06-04-2007, 01:51
BRUN,
I very much suspect that valvers have the holes as required on the tunnel.
Yeah, the heatshield is also bolted through it.
Mat.
how did you get the part number 60 01 025 886
i couldnt find it on dialogys
got it now :) didnt really know what i was looking for so missed it
ill order that from Renault today if they are open
My valver seems to have some sort of a hanger for the center section, i've noticed it before but never really investigated it!
Might have to get some pics!
Clio_GTT
06-04-2007, 13:09
got it now :) didnt really know what i was looking for so missed it
ill order that from Renault today if they are open
my 16v has one
thanks for all the info, its coming on Wed, gettin it fitted on Thurs
Here's some pics of my center section hanger - and this is on my Valver. Not something i've ever added, and i doubt the previous owner ever did..
http://i62.photobucket.com/albums/h120/cliokiz/exhaust%20hanger/mount2.jpg
http://i62.photobucket.com/albums/h120/cliokiz/exhaust%20hanger/mount1.jpg
Justin..
07-04-2007, 15:54
What year is your 16v cliokiz ?
VIPERONE
07-04-2007, 16:10
i have an after market hanger that is fixed using the rear towing eye metal..
MatBrown
07-04-2007, 16:35
Here's some pics of my center section hanger - and this is on my Valver. Not something i've ever added, and i doubt the previous owner ever did..
http://i62.photobucket.com/albums/h120/cliokiz/exhaust%20hanger/mount2.jpg
http://i62.photobucket.com/albums/h120/cliokiz/exhaust%20hanger/mount1.jpg
That looks like an aftermarket hangar that comes with an exhaust system.
Mat.
It's a '94 valver. M reg.
The K-TEC exhaust i took off before fitting the mongoose didnt use this hanger, so must've been an exhaust before then i guess..
I'll have to check to see if it's welded or bolted on.
MatBrown
08-04-2007, 11:04
It will be bolted in at a guess, looks like the one that comes with a magnex, even has the rubber they supply on it still.
Mat.
as far as im aware the willy has a centre section mount for the exhaust, to stop it hanging so low does anyone have any pics of it,
http://i60.photobucket.com/albums/h18/ppsun/P1010027.jpg
hmmm that doesnt look like its bolted on, more welded to the body of the car ???
cliokongen
08-04-2007, 22:10
A few pics....
Michael
A few pics....
Michael
That doesn't actually look like the standard Renault part :anyone:
MatBrown
08-04-2007, 23:01
as far as im aware the willy has a centre section mount for the exhaust, to stop it hanging so low does anyone have any pics of it,
http://i60.photobucket.com/albums/h18/ppsun/P1010027.jpg
hmmm that doesnt look like its bolted on, more welded to the body of the car ???
You can actually see the nut on the other side of the ridge.
Mat.
cliokongen
08-04-2007, 23:19
A few pics....
Michael
That doesn't actually look like the standard Renault part :anyone:
Hmm.... it should be the genuine article...
Michael
All of these pics, look different to the one i have fitted, and im certain it came from factory as it didnt want to come off lol.
Probably find theres so many as its a renault special; fit what ever they have in the parts bin.
hmmm that doesnt look like its bolted on, more welded to the body of the car ???
Another angle
http://i60.photobucket.com/albums/h18/ppsun/P1010071.jpg
again, that doesnt look like the others posted, and it doesnt look like the part on dialogys
thanks for the pics though, if it turns out i cant fit whatever comes from Renault on Wednesday then i have a few ideas of what we can do
It's a phase 2 clio williams. 12-year old exhaust unchanged from factory (except the cat). If it's wrong (won't be surprised that it is), shoot the Renault assembly worker! :)
lol, quite a funny quest this... maube i will go take some pictures later of how it is supposed to look :wink:
mine had that but it was knocking on the scorpion centre section so i cut it off :lol:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.