Page 1 of 4 123 ... LastLast
Results 1 to 10 of 32
  1. #1

    Oil Pressure reading zero :S

    Sensor failed? Won't read even if im driving around, was reading a bit earlier but then back to zero no matter how much I revved it, engine wasn't overheating and im guessing I would pretty quickly realise if the oil pump had gone?

    Where is the oil pressure sensor located? hard to change etc?

  2. #2
    Moderator
    Join Date
    Sep 2004
    Location
    Hinckley, Leics.
    Posts
    7,816
    Sensor is at the back of the block on the O/S, can get to it through the wheelarch with wheel off.
    Check all your connections first.


    Mat.

  3. #3
    Forum User 2 live's Avatar
    Join Date
    Sep 2004
    Location
    out there somewhere
    Posts
    7,399
    aye.....would say the wires come off.

  4. #4
    Forum User evouk's Avatar
    Join Date
    Nov 2006
    Location
    staffs
    Posts
    1,410
    whilst on topic of oil pressure, what does yours read just as you start engine up before it gets warm.

    clio 1.8 16v or williams :D

  5. #5
    Forum User
    Join Date
    Apr 2006
    Location
    Street, Somerset
    Posts
    195
    5 bar on startup. then when warm just over 1.

  6. #6
    Forum User 2 live's Avatar
    Join Date
    Sep 2004
    Location
    out there somewhere
    Posts
    7,399
    tbh...that depends on the oil used.


    mine sits at bout 5 on start up, but drops to barely reading on the gauge wen warm. diff oil.diff readings

  7. #7
    mines on 3 on the valver on startup! does that mean theres something not quite right?

  8. #8
    I'm with 2live, on start up when the oil is cold and viscous the oil pressure is really good, 5bar+ after its at runing temperature it drops to around 3bar+ when driving, and drops lower and lower on tick over as the engine gets warm and the oil starts to thin. was worried at first but its definately not the sender unit or sensors and the its simply down to te oil. going to change to silkolene from Guy at opie this time so wil see if that makes a difference.

  9. #9
    Quote Originally Posted by drsmith1979
    I'm with 2live, on start up when the oil is cold and viscous the oil pressure is really good, 5bar+ after its at runing temperature it drops to around 3bar+ when driving, and drops lower and lower on tick over as the engine gets warm and the oil starts to thin. was worried at first but its definately not the sender unit or sensors and the its simply down to te oil. going to change to silkolene from Guy at opie this time so wil see if that makes a difference.
    is that the best oil to use then? what thickness is best for my valver?

  10. #10
    Senior Member
    Join Date
    Sep 2006
    Location
    Rok a dale
    Posts
    1,698
    5.5 to 6 bar on start up when cold.

    Drops to around 3/4 when warm and general round town driving.

    same as above as well drops to around 1-0 on tick over when warm.


 

Similar Threads

  1. Yellow Dimma in Reading
    By jwarren2k2 in forum Was it you ?
    Replies: 0
    Last Post: 10-07-2007, 20:33
  2. Red valver in Tilehurst, Reading
    By dan-hipgrave in forum Was it you ?
    Replies: 0
    Last Post: 17-06-2006, 17:11
  3. Kitted M-reg 449 Valver in Reading
    By dan-hipgrave in forum Was it you ?
    Replies: 0
    Last Post: 14-06-2006, 16:47
  4. Reading
    By steveos_16valver in forum Local Meets/Events
    Replies: 10
    Last Post: 30-03-2006, 16:35
  5. Anyone here from Reading??
    By Tommo in forum Was it you ?
    Replies: 0
    Last Post: 11-08-2005, 14:31

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •