Search:

Vin plate isnt there as the above post, fairly sure its has a new front panel in, only reason i could tell was because it hasnt got the bolt out section like most valvers.

Perfect paint match...

Price drop to £899, come on folks dont make me strip the poor thing :(

Now on PH too

http://www.pistonheads.com/sales/1192178.htm

Ok guys , i know its only been a day , but am i asking too much ? :?

P.S comes with the original valver steering wheel , binned that silly red one :)

Right guys , dont really want to do it , but its gotta go. Its got 12 months mot and is taxed till the end of the month.

Spec and recent work carried out :-

Looks

Carbon fibre boot strip...

Upper cambelt cover. Lower crank pulley cover. Lower belt cover and pass side engine mount should be adequate for you to get some small hands in there.

Rhys , i think hes having doubts about the...

Not if you are using a one way bleed valve. The method above is a pain in the arse and ideally a 2 man job.

Personally I found the one man bleed kit where you use the spare tyre connected to the...

Nope , as long as you dont go silly on it. Copper bends far easier than the steel thats fitted from factory so you can lose some by making sweeping bends etc..

If you remove the old pipe from the...

Drivers side one 12" will do it, not sure on pass im yet to replace it :)

Sorry this is late but i found it trying to find the brake order.

You cant just pump the pedal with the nipple open.

Pedal down
Open nipple
Close nipple
Pedal up

Pumping it will just...

I have one of these, very capable cars. 165 bhp standard and handling to boot.

You got spark ?

Whrring be careful of , hope its not the cambelt, major common problem on the pugs.

Oohhh , what am i looking for in terms of stock and kent ?

Only thing not standard internally would be the cams. This is why i only estimated 15 bhp over stock for the exhaust, filter and chip. Being a rebuild the compression is as new aswell.

I...

Sorry if this is the wrong section , it was the most appropriate i could find based on the headings.

Its been short lived , but i bought this car as a track car. After doing some work and getting...

http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=250476880591&ssPageName=STRK:MESELX:IT

Discount for forum members :)

I assumed he was stationary when dipping clutch and engaging first, if you are indeed moving then go with the above advice, if your stationary then it wont be speed sensor.

Hello mate, im in west midlands , ws10 area.

Any good ?

Mainly bonnet please, also could do with bootlid.

Bonnet preferably for a 16v or willy but possibly accept a poverty spec one too.

Cheers

Sounds like the clutch is on its last legs and the auto adjuster is at the end of its adjustment to me.

To test, get a jack on the clutch arm and disegnage the clutch fully and check if it still...

No not tried another , but resistance wise it works fine ?

What other cars have the same one so i can get pilfering in the scrappy lol.

Ok , had a butchers...

Anti purculation system is working fine , water pump runs after turn off when its hot , but the fan doesnt run at this stage and neither does it run when the engine gets...

Trouble is it only holds back and kangaroos when this is plugged in , unplug it and it runs fine but idles high.

Is it possible that unplugging it is hightlighting a problem with another sensor ?...

When i do this , i get a sever hold back when i put the slipper down , then a few seconds later it shoots of like a rocket, is this bad adjustment ? or is it possible that when this is plugged in it...

Right , when my TPS is plugged in the car kangaroos and holds back then shoots off like a rocket.

Unplugged it runs fine but idles high.

I tested the resistance and its 2.2k at closed and 6.2k...

Sorry to drag this up , but i tested mine last night.

The two outside wires are simply varied resistance between each other , hence the sensor is actually a variable resistor , or potentiometer.
...

Ok , did some searching and got a few answers guys , so cheers.

It appears that the temp sensor in the rad controls fans whilst its running , and the CTS controls when its turned off ?

Third...

Hi guys , in the bid to sort any niggles before a track day id like some info on when the fan kicks in and how its controlled please.

Where should the temp sit on the gauge ? bang on halfway or is...

Nice one , cheers folks , it is indeed the dash sensor, it was still working by a strand.

Got it all running nice now , new plugs, leads, cam , arm and cleaned the iscv out , was filthy.

Tested...

Need a willy wheel or valver wheel with the assosciated fitting bits , so the rotary coupler and any gubbins to turn the indicators off and stuff.