Starter Motor Fitting

[Willbee]

OK, I'm having a little trouble replacing my starter motor. I've got the three big mounting bolts out but its still solidly in place. Can someone tell me where the remaining fitting(s) is/are please! One possibility is a small nut at the back end of it, but I'm not sure.

Many thanks,
Will

[schakal]

that should be all the bolts mate , however there is a locating dowel
in one of the top holes ,that might be holding it in place ??

Like i always say ;

If in doubt ,get the hammer out 8)

[2 live]

have you taken the bracket off thats bolted to the back of the starter and the block???

better try that 1st than smash it to bits with a hammer :roll:

[chip]

FLOL

[2 live]

once again, ill informed advice given by someone who knows everything about **** all. ;)

[schakal]

once again, ill informed advice given by someone who knows everything about f**k all. ;)

You always trying to piss further than i do says otherwise
though mate :wink:

[McPikie]

I'm going to crack your heads together soon

[2 live]

once again, ill informed advice given by someone who knows everything about f**k all. ;)

You always trying to piss further than i do says otherwise
though mate :wink:

maybe, just maybe, im trying to save other members money/time your bad advice would otherwise cause them to spend.

[TooSkive]

How very noble of you 2 live, very selfless, you seem like such a decent human being.

Your Williams must be mint and mechanically sound too I'm sure :)

[2 live]

lol. arent you banned? or about to be again? or schaks with a new profile?

:roll:

[Evogone]

How very noble of you 2 live, very selfless, you seem like such a decent human being.

Your Williams must be mint and mechanically sound too I'm sure :)

Sponge rob...... :wink:

[TooSkive]

lol. arent you banned? or about to be again? or schaks with a new profile?

:roll:

I was simply pointing out how helpful you have been. The forum needs more members like you :D

[James5]

to save opening another thread are F7p and Fr6 starter the same?? I know the later meganne f7r's with coilpack maybe different, but the williams F7r and f7p?

[2 live]

lol. arent you banned? or about to be again? or schaks with a new profile?

:roll:

I was simply pointing out how helpful you have been. The forum needs more members like you :D

im sure cerain members would disagree lol.


and f7r/p starters are diff.

[dkrevs]

No Williams starter is different to the Valver one. It's smaller because of different engine block.

[2 live]

arent the teeth diff too? been a good while since i messed with either engine tbh.

[dkrevs]

arent the teeth diff too? been a good while since i messed with either engine tbh.
Not that I know, but with Renault everthing is possible.

[dkrevs]

*everything

[schakal]

once again, ill informed advice given by someone who knows everything about f**k all. ;)

You always trying to piss further than i do says otherwise
though mate :wink:

maybe, just maybe, im trying to save other members money/time your bad advice would otherwise cause them to spend.

An adult man like yourself should not be looking for ego boost
on a car enthusiasts forum . I can only assume your gaydar subscription ran out again ?? :D

[2 live]

here we go again :roll:

[MAXIBOY]

back on topic if iirc there are 9 or 10 tooth versions or the 16 valve and different size versions (smaller) on the megane and willy both iirc 9 tooth versions

[2 live]

yeah i thought there were 2 diff tooth ones. wasnt sure tho.

[adiclio16v]

I had a 1.2 starter motor on my red hybrid wen the willy 1 packed in worked alrite
I changed it with an adjustable spanner and a very large hammer lol
adi

[2 live]

no doubt with your cock in yer hand too. lol

[Jamie.]

Enough.

Constant moaning and arguing and ruining other peoples threads.

Any more from anyone and I think a ban for a period of time is needed.

No one is trying to wind anyone else up - lifes to short.