turbo set up and forged engine

[walters300]

:( just seen laines set up and i want one :x have itbs forsale on here but if i could sell my turbo set up would go over to itb's, not as much power but sound :D , bits are in ireland but i could pallet them over. PM me if your interested. F7R fully rebuilt with less than 500 miles with everything you will need, cost me a lot more than it should have and i will consider good offers. around 2k is my idea of reasonable, considering it cost 3k for just the engine. cmon dudes buy it!!!!!!!!!! also includes high boost chip/ low boost chip/ FPR/ boost gauge/ dump valve/ recirc valve/ manual boost controller/

[Laine_16v]

:wink:

[schakal]

taking Laine as a role model ?? ----- PRICELESS

on a side note ;
its only working fine cause he has not yet
bounced it off the limiter pulling out the drive or put some sugar on it .


:wink:

[walters300]

:P shacks Laine has had months of head holding and burst out of the blocks with part 8) would say part 2 is going to be a different kettle of fish, Itbs just sound loooovvvveeeely. turbo is fantastic though :D and better than itbs ( this is my sales thread :lol: ) one thing here is that you will have big power. 270BHP and safe for little money. will need a rolling road to confirm fueling etc. or if you live near (KJ) aka turbo specialist , he will sort it out propery for you. BARGAIN LADS!

[walters300]

This is a copy of the mail for the works done, i didnt get a receipt as i managed to get him down to 1200 for cash, i also put a new water pump, cambelt kit and sensors which was another 500 from renault ireland, also spent another 1k with BB tuning on pistons/ rods/ ARP bolts/ gasket/ platinum plugs. its only done 500 miles since at very low revs to run in, comes with all the bits required to make a good install,






Barry this is a break down of the parts and machining costs. these are trade prices and are totally necessary to ensure a good job. Labour is totalled up at 23.75hours, as this is a one off job and I couldn't estimate for you I have compromised to 16hrs, these are usually charged at retail 45/hour I am charging you trade of 35/ hour. this comes to ?560... plus the machining totals ?1400


Regards

Donnacha



Cork Engine Centre
Unit 26, Rockgrove Industrial Estate,
Little Island, Cork
Telephone: +353 (0)214 35 45 35 TEL:4506700
VAT No.: IE6922992P
Engine Re-manufacturing
Advice Note - Proforma
BARRY WALTERS
35 Oakfield Ave
Glanmire
Co.Cork
Job ref.:
Date:
TRADE
Account:
A 779
22/05/08
Reg No./VIN:
Model:
0174
RENO CLIO
Eng/Chass
/Body:
Miles/Km.





Order:
ReNAULT CLIO WILLIAM

Qty
Item
Number
Description
Hrs.
Unit
Cost


1
77752600 BIGENDS STD RENO
"
61.75
61.75
0.00
1
77090608 MAINS STD RENAULT
"
75.60
75.60
0.00
1
THRUST WASHER 78859608 STD
"
22.04
22.04
0.00
1
DISMANTLE WASH AND REASEMBLE
Recondition
60.00
60.00
0.00
1
DE-COKE CYLINDER HEAD
"
.00
.00
0.00
1
SURFACE GRIND CYLINDER HEAD
"
48.00
48.00
0.00
16
FVS
FIT VALVE STEM OIL SEALS
Replace
1.00
16.00
0.00
16
REFACE VALVE SEAT
Recondition
8.00
128.00
0.00
16
REFACE VALVE
"
5.00
80.00
0.00
16
DB
DRAIN HYDRAULIC FOLLOWERS
Replace
2.00
32.00
0.00
1
OIL DISPOSAL CHARGE
"
6.00
6.00
0.00
1
REBORE BLOCK 82.93MM
"
180.00
180.00
0.00
4
HONE BLOCK TO SUIT
"
10.00
40.00
0.00
1
SURFACE GRIND BLOCK DECK
"
48.00
48.00
0.00
1

POLISH AND MEASURE CRANKSHAFT
"
50.00
50.00
0.00
AutoPro©
12/06/08
PAYMENT TERMS: Nett 30 days from end of month.
By:Administrator