Laine_16v
26-10-2009, 01:35
Here we have a great opportunity to get your mitts on a set of throttle bodies and just about everything needed to make them run on your motor.
Heres what your get:
2 x Twin 45 DCOE Throttle Bodies (Retails at £455 inc VAT)
1 x Throttle Linkage Kit (Retails at £153 inc VAT)
1 x Webber Fixed FPR (3 bar) (Retails at around £60)
2 x Forged Ally Fuel Rails to suit ITB's (Retails at £87 inc VAT)
4 x Bosch 289cc Injectors (Retails at around £250)
1 x Pipercross C603D Sausage Type Air Filter (Retails at £68)
4 x 90mm Air horns in fair coniditon (Retail at £110 inc VAT)
1 x Bespoke FIbreglass AIrbox Backplate (£50 + £20 to have it shaped and drilled)
1 x Low Profile Custom Ally Radiator to suit Valver / WIlliams (£350)
1 x Kenlow Fan ( i think) (£60)
1 x VEMs ECU FUlly Assembled Model v3.3 (£430)
1 x Handbuilt Custom loom for Valver/Williams (£50)
1 x TDC Sensor (£20)
As you can see all this adds up to £££££££££
All the kit is in very good condition indeed apart from the air horns which are a bit marked,, but you dont see them anyway.
What you need to make it run...
A DCOE inlet manifold to suit your engine (Supplied from CHadil ,Jenvey e.t.c)
Injector blanking plugs for your cylinder head
A Dizzy'less coil pack setup
172 / Meganne Flywheel
THe throttle bodies have been taken off the car stripped down and cleaned and look spanking. The trhottle linkage kit has also been dissasembled cleaned painted and then reassembled. FUel rails have been sprayed silver.
This kit could fit on an Williams / Valver, or with a small amount of work to the cooling system and wiring a clio 172.
I hand built the loom its very tidy all wires are correct length e.t.c Has built in manual fuel pump manual fan ,and main power overide switchs for dashbaord.
THe ECU Comes with a 2.0 Cammed ITB'd forged map already on it and should get you running
Jenveys are tried and tested the best Throttle body kit out there buy yourself a nice early Xmas present ;)
£1500.
Heres what your get:
2 x Twin 45 DCOE Throttle Bodies (Retails at £455 inc VAT)
1 x Throttle Linkage Kit (Retails at £153 inc VAT)
1 x Webber Fixed FPR (3 bar) (Retails at around £60)
2 x Forged Ally Fuel Rails to suit ITB's (Retails at £87 inc VAT)
4 x Bosch 289cc Injectors (Retails at around £250)
1 x Pipercross C603D Sausage Type Air Filter (Retails at £68)
4 x 90mm Air horns in fair coniditon (Retail at £110 inc VAT)
1 x Bespoke FIbreglass AIrbox Backplate (£50 + £20 to have it shaped and drilled)
1 x Low Profile Custom Ally Radiator to suit Valver / WIlliams (£350)
1 x Kenlow Fan ( i think) (£60)
1 x VEMs ECU FUlly Assembled Model v3.3 (£430)
1 x Handbuilt Custom loom for Valver/Williams (£50)
1 x TDC Sensor (£20)
As you can see all this adds up to £££££££££
All the kit is in very good condition indeed apart from the air horns which are a bit marked,, but you dont see them anyway.
What you need to make it run...
A DCOE inlet manifold to suit your engine (Supplied from CHadil ,Jenvey e.t.c)
Injector blanking plugs for your cylinder head
A Dizzy'less coil pack setup
172 / Meganne Flywheel
THe throttle bodies have been taken off the car stripped down and cleaned and look spanking. The trhottle linkage kit has also been dissasembled cleaned painted and then reassembled. FUel rails have been sprayed silver.
This kit could fit on an Williams / Valver, or with a small amount of work to the cooling system and wiring a clio 172.
I hand built the loom its very tidy all wires are correct length e.t.c Has built in manual fuel pump manual fan ,and main power overide switchs for dashbaord.
THe ECU Comes with a 2.0 Cammed ITB'd forged map already on it and should get you running
Jenveys are tried and tested the best Throttle body kit out there buy yourself a nice early Xmas present ;)
£1500.