stan
01-05-2008, 11:27
Right, after alot of intrest, im posting here to give clear prices on my ITB installs.
This is based on a drive in/drive out set-up, fully warranteed, using the best components available for our needs and the cost involved (good ol' tried/tested/proven jenveys), built to the highest quality, properply set-up, fully mapped to optimise torque, power and fuel efficiency, ready to go and thrash the arse off!
The parts list:
-Emerald K3 ecu (offers the same function and ability as any other ecu check www.emeraldm3d.com for full spec.)
-Jenvey ITB's (inc all accessoris, trumpets, linkage etc etc etc etc, everything needed)
-Foam "sausage type" filter
-CUSTOM ALUMINIUM RAD and fan (required for a neat and properly functioning install---alone costing £500)
-Specific HANDMADE loom (not an over-length generic item, with the OE loom half hanging off)
-full mapping and optimisation session on a fully calibreated (required to give realisitc figures...who needs overinflated ones? with printout on full dynamometer software)
The price:
£3100 (inc rad/fan)
Can also be supplied in kit form to suit your needs/budget/skill level of fitting/ammount you can DIY.
Just to clarify a few points:
My prices are, on the whole, cheaper then anyone else worth mentioning. This is SIMPLY because of my loacation. My over-heads are ALOT less than those based elsewhere in the UK, therefore my profit margins can be the same as others, with a lower custome rprice! meaning i dont have to bump up YOUR costs to make a living. This does not in any way affect technical input or ability. Those who have dealt with me, foned for advice, had work done by my etc will all tell you my work and ability is right up there, I dont mess around.
As for location, 90% of my customer base is from outside Wales. in most cases i would say they travel 200miles. in some cases 400miles. This really does spk for itself.
I can also offer a price-match, where if you send me a formal quote in email or snail-mail form for work you've discussed elsewhere, I will beat it.
Regards
Craig
This is based on a drive in/drive out set-up, fully warranteed, using the best components available for our needs and the cost involved (good ol' tried/tested/proven jenveys), built to the highest quality, properply set-up, fully mapped to optimise torque, power and fuel efficiency, ready to go and thrash the arse off!
The parts list:
-Emerald K3 ecu (offers the same function and ability as any other ecu check www.emeraldm3d.com for full spec.)
-Jenvey ITB's (inc all accessoris, trumpets, linkage etc etc etc etc, everything needed)
-Foam "sausage type" filter
-CUSTOM ALUMINIUM RAD and fan (required for a neat and properly functioning install---alone costing £500)
-Specific HANDMADE loom (not an over-length generic item, with the OE loom half hanging off)
-full mapping and optimisation session on a fully calibreated (required to give realisitc figures...who needs overinflated ones? with printout on full dynamometer software)
The price:
£3100 (inc rad/fan)
Can also be supplied in kit form to suit your needs/budget/skill level of fitting/ammount you can DIY.
Just to clarify a few points:
My prices are, on the whole, cheaper then anyone else worth mentioning. This is SIMPLY because of my loacation. My over-heads are ALOT less than those based elsewhere in the UK, therefore my profit margins can be the same as others, with a lower custome rprice! meaning i dont have to bump up YOUR costs to make a living. This does not in any way affect technical input or ability. Those who have dealt with me, foned for advice, had work done by my etc will all tell you my work and ability is right up there, I dont mess around.
As for location, 90% of my customer base is from outside Wales. in most cases i would say they travel 200miles. in some cases 400miles. This really does spk for itself.
I can also offer a price-match, where if you send me a formal quote in email or snail-mail form for work you've discussed elsewhere, I will beat it.
Regards
Craig