PDA

View Full Version : What to replace while box is off ??



BRUN
07-03-2008, 11:40
money is tight but if it makes sense to replace something then i will

of course im doing the clutch, and also the mount on top of the box aswell

is there anything else i should consider

mike16valver
07-03-2008, 11:47
I think u have covered it matey,

I can't think of any thing else that u could replace around that section, what u havnt alrdy mentiond.

Maybe other members mite , Just check they wiring make sure nothing is left Loose or hanging.

I had a the Oil temp plug fecking hanging about, when my fan came on it eventually vibrating the lil feck apart.

mike

BristolSam16v
07-03-2008, 13:13
If your speedo wobbles then its def worth changing the clip in the box when its out, far far easier.

white16valver
07-03-2008, 13:40
Gearbox oil :P lol

u33db
07-03-2008, 13:55
Flywheel sensor?

BRUN
07-03-2008, 14:57
that was replaced soon after i got it from you mate, tried that to solve the poor starting but it turned out to be the ignition coil was weak

so you know if any of the mounts have ever been done on this car ?

u33db
07-03-2008, 14:58
Top mount and dogbone were defo done...can't remember about gearbox one though..probably! lol

BRUN
07-03-2008, 15:28
well ive replaced the dogbone again a few months back, as long as i dont have to worry about the main mount

katbloke
07-03-2008, 16:18
cable?

lukebartlett2405
07-03-2008, 17:04
Good time to convert to a soft clutch

mike16valver
07-03-2008, 17:09
Good time to convert to a soft clutch

Was guna mention this too, Last time it was brought up, they was Call a wuss, thats for gurl, bla bla bla,

Kept my mouth shut, :-#

Mike

Chris H
07-03-2008, 18:26
only fool wouldn't replace the release lever and the pivot bush, especially the pivot bush!

BRUN
07-03-2008, 18:53
decided im going for a refurb Renault box !

i presume the release lever and pivot bush are inside the box ?....sorry, i know nothing about gearboxes

eternalife
07-03-2008, 18:58
only fool wouldn't replace the release lever and the pivot bush, especially the pivot bush!

Personally I would do the Pivot bush (as previously someone reported a worn pivot bush which resulted in difficulty changing to lower gears when the car was getting hot in traffic) and for the cost of £1.50 its not gona hurt the pocket.

Although, the same problems/symptoms have had different remedies - such as pressure plate and clutch cable.

You are getting the compelte clutch kit are you not?

105epwr
07-03-2008, 18:58
I would change the rear main oil seal while you was there.
part number r7703087190 18 quid

number1
08-03-2008, 13:10
As Chris said! maybe consider the soft pedal conversion if your going for an uprated clutch, Also Check that the 3 bolts that holds the n/s driveshaft gaitor in have good clean threads, if they strip when you have got the box back in then someone will be annoyed

BRUN
08-03-2008, 18:59
going for a standard clutch, its always been fine

valver_Karl
08-03-2008, 19:06
wot parts are needed to do a soft pedal conversion? and is it easy to do?

number1
08-03-2008, 22:48
You need a Megane/Laguna/Volvo clutch release arm and the extender bracket for the cable to sit higher on, some say you need a longer clutch cable but mine has been fine, i have a couple spare extender brackets here thinking about it

valver_Karl
08-03-2008, 23:02
oh right kl. im puttin a willy lump in my valver, comes with box, the box will need to come off wont it?

number1
09-03-2008, 12:47
yeh the box will have to come off, piece of cake when the engines out the car, make sure you do the clutch pressure plate bolts in an opposing sequence to avoid bending the release springs

stan
09-03-2008, 13:02
Thye foul the airbox...obviously not an issue if your running and induction kit.

valver_Karl
09-03-2008, 14:06
gettin throttle bodies

valver_Karl
09-03-2008, 14:06
gettin throttle bodies