View Full Version : Picked my first Williams up..... Fec queries...
Ok so ive picked up my first Williams clio 2 and I love it... I got it cheap £1500 as its not mint but has thousands in recent receipts plus a full documented service history upto 120k which it is on...
Few questions though?
The reve counter doesnt ork but occasionally it will spring into life then die again, any ideas?
The alloys need a refurb any ideas as to where im in Windermere, Cumbria?
The 3 clocks in the cantre the oil ones the far left one doesnt seem to move it says min max but never moves and I have no idea what it is? The ither 2 oil pressure stays above 3 at 60mph and temp is around 100, is this ok?
The little bloody temp on the clocks themselves between speedo and rev just flashes at me 50 c is it knackered, can I rsset it or do I put some tape over it?
Sorry for all the questions but didnt know where to start?
Will post more quesries soon...
Steve
Bailey_1260
15-07-2007, 18:22
Cant help with all of them but for wheel refurb yellow pages are your friend.
And Oil clock on far left is oil lever and only shows when ignition is on BEFORE engine has been started, after that it will drop to 0 again.
Hope this helps a little.
Also wht number is it?
Bailey
Justin..
15-07-2007, 18:34
The reve counter doesnt ork but occasionally it will spring into life then die again, any ideas? Common problm usually rectified by replacing the dial
The alloys need a refurb any ideas as to where im in Windermere, Cumbria?
The 3 clocks in the cantre the oil ones the far left one doesnt seem to move it says min max but never moves and I have no idea what it is? As already said belowhow it works. If its showin nothing at all on pre ignition check your dipstick asap!!!
The ither 2 oil pressure stays above 3 at 60mph and temp is around 100, is this ok? Thats sounds about right
The little bloody temp on the clocks themselves between speedo and rev just flashes at me 50 c is it knackered, can I rsset it or do I put some tape over it? Sounds like the sensor is knackered. Its the nipple on the passanger wing mirror. May just be dislodged though hopefully
I dont know what number it is as it a williams 2 and I didnt think they had a number????
So if I remove the clocks and take the reve counter out will a 16valve one fit? How easy is it to remove the clocks?
Thanks for all the advice you lot really are superb.... I also need a drivers headlight as its cracked plus a fog light as its cracked....
Steve
PS I drove it back from Bristol and what a fantastic drive and they still turn heads wherever they go..........
Justin..
15-07-2007, 19:41
Nope, only the Williams' had numbers. Willy 2 & 3 werent graced with that.
Yeah straight swap. Easy to remove for an amateur
valver rev counter will fit but it wont be blue will it???? williams 2's were not numbered...
the oil level question always pops up from newbies on the site :wink:
glad you enjoyed ya trip home
Justin..
15-07-2007, 19:42
You can just swap the guts over FB :wink:
Yeah will just swop the guts over, how easy are the clocks to remove though?
Steve
Also looking at all this de-cat stuff someone has offered me a cat that has had all its guts pulled out so what benefits would I get from this? Or am I wasting my money?
Steve
Question, with the standard aerial how do they come off? Do they just twist off the base? Wanna put a stumpy on but tried twistin it and it didnt seem to wanna come... Dont want to break anything....
Steve
the whip(long aeriel) will twist out of the base as its threaded..
Justin..
15-07-2007, 20:31
yeah probably seized hence seems stuf. ont forget its been there nearly 13 years or so :lol:
unbolts from the inside. hello and welcome by the way
Thanks so basically just twist pretty hard and keep trying???
And by the way what a friendly helpfull lot.....
Steve
Justin..
15-07-2007, 20:37
yeah, but it might just twist off leaving the threaded bit
you wont find a more helpfull comunity imo
remove the interior light and the fixings as there.
Justin..
15-07-2007, 20:38
think he just want to change the ariel over for a stumpy not remove the whole assembly
Yeah just the aerial for a stumpy not the whole lot.... Cheers
Steve
Bailey_1260
15-07-2007, 21:39
Nope, only the Williams' had numbers. Willy 2 & 3 werent graced with that.
My bad sorry :oops:
Welcom BTW
MatrixGuy
17-07-2007, 12:32
You got any pics mate?
We should hook up sometime, i live in Lancaster :)
Did you get my PM?
busterhymes
17-07-2007, 12:37
girlfriend lives in carnforth maybe keep a look out when i'm visitin in my willy :D :D :D :D
MatrixGuy
17-07-2007, 12:47
girlfriend lives in carnforth maybe keep a look out when i'm visitin in my willy :D :D :D :D
awesome, lol.
do u have a willy bud?
Yeah just the aerial for a stumpy not the whole lot.... Cheers
Steve
Still may have to though - Mine REFUSED to leave its 13 year old home so In the end I replaced it all and lubricated it to stop it from doing it again!
My oil pressure runs at 3k at 75 ish, at 60 its just over 2, poss 2.5. Mine has always seem to had lower pressures then other peoples.
fasterthanjesus
17-07-2007, 22:06
welcome.
im in lancaster, some very nice roads near you mate. enjoy!
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.