View Full Version : changing clutch pedal....
hi guys,
need to change my clutch pedal as the ratchet is fooked!
just wondering if anyone has a guide or any tips?
i'm kinda hoping it's not that hard.. :?
any advice would be much appreciated.
cheers
Ian
not really hard but fiddly. don,t think there,s a guide
Lee Keefy
13-02-2007, 22:15
not to go off topic but should the clutch arm bushes be held in by some means :?: :?
think there held in by the pedal bracket sides once assembled. will look it up now.
cheers for the replies.
how long do you think it will take?
Lee Keefy
13-02-2007, 22:32
i would say about an hour ish depending on how sick you feel bein on your back for that long :wink:
i usually wind the seat back and lie on that with my head under the dash though :roll:
lee have you done it recently?
any tips?
Lee Keefy
13-02-2007, 22:36
no i just keep havin to put this piggin bush back in...
just have a good look b4 you start and remember where it all goes :wink:
make notes take photo,s as you remove the old one so you get the bushes the right way round. also there is a guide in the haynes manual. have you got one otherwise i could scan it and e-mail it to you. or post it up.
ok cheers buddy.
i was hoping that someone may have a guide for changing it..
oh i take it the williams and 16v pedals are the same?
maxiboy, if you could do that, it'd be awesome buddy :D
http://i36.photobucket.com/albums/e15/123maxiboy/File0142.jpg
http://i36.photobucket.com/albums/e15/123maxiboy/File0144.jpg
hope these come out ok. otherwise i,ll e-mail you the original scans
cheers buddy...
do you think you can email me the original scans as well please?
thanks
yes mate whats you e-mail. pm me if you want i,ll do it now
Lee Keefy
13-02-2007, 23:24
yes mate whats you e-mail. pm me if you want i,ll do it now
that f**ckin clip is the root of all my problems!!!!!
should it go on the driver or passenger side of the pedal??? i cant make it out in the pics :shock:
BigBoreBri
13-02-2007, 23:59
From what i remember the easiest way is to first familiarise yourself with the clutch assembly...
1. Release the clutch cable from the selector fork (remove the air box for access)
2. Push the pedal to the floor to release the ratchet and release the clutch cable
3. Remove the clutch pedal retaing clip (left hand side)
4. Remove the 2xM10 Nuts and pedal assembly side housing...
4. Then pull the other retaining clip together and slide the shaft out (right hand side)
5. The clutch cable will most likely just fall to bits now... lol
6. Assemble the new clutch pedal assembly and spring holding it together...
7. Slide the shaft back through making sure the bushes stay in place
8. Re-attatch the side housing and tighten up...
9. Best thing i found now is to remove the right hand retaining clip!
10. Secure the clutch pedal retaining clip on the left hand side...
11. There is a tab to slide a screw-driver in to prise the shaft across...
12. This should allow you to prise the right hand retaining clip back in!
13. Attatch the clutch cable to the pedal assembly
14. Attatch the clutch cable to the selector fork
15. Pump the pedal to self-adjust the ratchet mech...
16. Make a coffee and eat a few cookies!
:lol:
Lee Keefy
14-02-2007, 19:09
passenger side i think
passenger side its goin on then!!!!
cheers :wink:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.