PDA

View Full Version : williams doors and 16v doors



wrighty
26-10-2006, 18:57
Forgive what may be a stupid question but I assume a clio 16v mk1 doors will fit a williams 2? (Both front and boot lid)

Is the complete body the same? Thanks for any help!

Paul

Winston
26-10-2006, 18:59
Yes they will fit no probs

Ph2 16v parts will be 100% spot on for a williams 2

richy
26-10-2006, 18:59
yeah should fit fine, think later ph2 have side impact bars though, only thing im not sure on is when the door strip fits, never looked at both without the strips tbh!

wrighty
26-10-2006, 19:03
Thanks! Hopefully the phase 1 doors will be ok! We shall see if i get some!

Shame its not a phase 2 clio 16v doors I may have found!!

Winston
26-10-2006, 19:05
^Side strips use different clips between Ph1 and 2...doors the same tho^

A williams 2 is a ph2 :wink:

Ph2 doors have side bars ...as richy says
Ph2 Tail gates down have a washer jet hole as it's on the wiper

wrighty
26-10-2006, 19:09
So a phase 1 clio 16v doors no good for my willy 2? I take it the metallic blue is the same?

What about the lower boot strip that is different between the phase 1 and 2s?

Thanks again!

Paul

white16valver
26-10-2006, 19:13
I believe they're both 449 blue so should be fine, although pain always changes over time so you will very probably only get a 98% match rather than a perfect match.

The tailgate trim is just a piece of plastic and can be swapped over to ph2 spec - I'm sure someone on here will have one!

Winston
26-10-2006, 19:14
Both Ph's of door will fit and look the same .....just one will have a bar in and the other won't lol

The boot strip is different Ph1 is grey with badges...Ph2 is carbone stylee to match the lights

449 blue is shared with valvers J-Mreg

wrighty
26-10-2006, 20:13
Thanks for your help, as always very much appreciated!


Paul

fasterthanjesus
26-10-2006, 20:29
done both my drivers door and tailgate.

the drivers door needed the hinge pulling slightly to get a nice fit, both door and tailgate were re-sprayed.

got my door for 99p from ebay!

wrighty
26-10-2006, 21:05
Bargain that!

Cant seem to find any at the mo and most breakers dont even bother getting back to me!

merlin
26-10-2006, 23:08
I to have been in touch with a lot of breakers who dont bother to even reply,most of em on ebay some kind person decided to kick my drivers door near the handle and now it wont close on the second latch.had the car about 5 weeks so maybe time to sell N reg 16v fitted williams motor
lots of new parts fitted just dont like the car,going to put add in cars for sale with pics asap.ken

POWARTEK
27-10-2006, 01:52
surely doors from a std 3dr clio fit?

nyk
27-10-2006, 08:35
^^^well the windows do^^^

I replaced my passenger window with one off a 3 door 1.2.

Winston
27-10-2006, 12:39
As above

Any 3 door clio door or tailgate will fit .....with the same Ph1 and 2 rules as above

Got the idea you were looking for a 449ner

MatBrown
27-10-2006, 17:51
Me too, pretty sure he is.



Mat.

wrighty
29-10-2006, 21:37
Thanks for all your help guys, managed to source a valver that I intend to swap the best bits over with! Turned out easier to get the whole car than each bit separately!

To that end over the next few weeks most bits will be available for sale other than body parts etc so if anyone is in need of bits let me know!

Thanks again for the help!

Paul